| Home |
 |
Chapter 5 |
|
Access
Time — Time between the memory's receiving a new input address and
the output data's becoming available in a read operation. Return
to Top
ZIF — Zero-insertion-force IC socket.
Accumulator — Principal register of an
arithmetic/logic unit (ALU).
Acquisition Time — Time required
for a sample-and-hold circuit to capture the analog value that is present on
its input.
Active-HIGH (LOW) Decoder —
Decoder that produces a logic HIGH (LOW) at the output when detection occurs.
Active Logic Level — Logic level
at which a circuit is considered active. If the symbol for the circuit includes
a bubble, the circuit is active-LOW. On the other hand, if it doesn't have a
bubble, then the circuit is active-HIGH.
Actuator — Electrically controlled device
that controls a physical variable.
Addend — Number to be added to another.
Adder/Subtractor — An adder circuit
that can subtract by complementing (negating) one of the operands. See also
Parallel/Adder.
Address — Number that uniquely identifies
the location of a word in memory.
Address Bus — Unidirectional lines that
carry the address code from the CPU to memory and I/O devices.
Address Multiplexing — Multiplexing
used in dynamic RAMs to save IC pins. It involves latching the two halves of
a complete address into the IC in separate steps.
Alias — A digital signal that results from
sampling an incoming signal at a rate less than twice the highest frequency
contained in the incoming signal.
Alphanumeric Codes — Codes that
represent numbers, letters, punctuation marks, and special characters.
Altera Hardware Description
Language (AHDL) — A proprietary HDL developed by Altera Corporation
for programming their programmable logic devices.
Alternate Logic Symbol — A
logically equivalent symbol that indicates the active level of the inputs and
outputs.
Analog Representation — Representation
of a quantity that varies over a continuous range of values.
Analog System — Combination of devices
designed to manipulate physical quantities that are represented in analog form.
Analog-to-Digital Converter (ADC)
— Circuit that converts an analog input to a corresponding digital output.
Analog Voltage Comparator —
Circuit that compares two analog input voltages and produces an output that
indicates which input is greater.
& — When used inside an IEEE/ANSI symbol, an indication
of an AND gate or AND function.
AND Gate — Digital circuit that implements
the AND operation. The output of this circuit is HIGH (logic level 1) only if
all of its inputs are HIGH.
AND Operation — Boolean algebra operation
in which the symbol · is used to indicate the ANDing of two or more logic
variables. The result of the AND operation will be HIGH (logic level 1) only
if all variables are HIGH.
Application-Specific
Integrated Circuit (ASIC) — An IC that has been specifically designed
to meet the requirements of an application. Subcategories include PLDs, gate
arrays, standard cells, and full-custom ICs.
ARCHITECTURE — Keyword in VHDL used
to begin a section of code that defines the operation of a circuit block (ENTITY).
Arithmetic/Logic Unit (ALU)
— Digital circuit used in computers to perform various arithmetic and
logic operations.
ASCII Code (American Standard Code for Information Interchange)
— Seven-bit alphanumeric code used by most computer manufacturers.
Asserted — Term used to describe the state
of a logic signal; synonymous with "active."
Astable Multivibrator — Digital
circuit that oscillates between two unstable output states.
Asynchronous Counter — Type
of counter in which each flip-flop output serves as the clock input signal for
the next flip-flop in the chain.
Asynchronous Inputs — Flip-flop
inputs that can affect the operation of the flip-flop independent of the synchronous
and clock inputs.
Asynchronous Transfer — Data
transfer performed without the aid of the clock.
Augend — Number to which an addend is added.
Auxiliary Memory — The part of a
computer's memory that is separate from the computer's main working memory.
Generally has high density and high capacity, such as magnetic disk.
Backplane — Electrical connection
common to all segments of an LCD.
Barrel Shifter — A shift register
that can very efficiently shift a binary number left or right by any number
of bit positions.
BCD Adder — Special adder containing two
four-bit parallel adders and a correction detector circuit. Whenever the addition
of two BCD code groups is greater than 10012 (910), the
correction detector circuit senses it, adds to the result the correction factor
01102 (610), and generates a carry to the next decimal
position.
BCD Counter — Binary counter that counts
from 00002 to 10012 before it recycles.
BCD-to-Decimal Decoder — Decoder
that converts a BCD input into a single decimal output equivalence.
BCD-to-See Section 7-Segment Decoder/Driver
— Digital circuit that takes a four-bit BCD input and activates the required
outputs to display the equivalent decimal digit on a See Section 7-segment display.
Behavioral Level of Abstraction
— A technique of describing a digital circuit that focuses on how the
circuit reacts to its inputs.
Bidirectional Data Line —
Term used when a data line functions as either an input or an output line depending
on the states of the enable inputs.
Bilateral Switch — CMOS circuit
that acts like a single-pole, single-throw (SPST) switch controlled by an input
logic level.
Binary-Coded-Decimal Code (BCD Code)
— Four-bit code used to represent each digit of a decimal number by its
four-bit binary equivalent.
Binary Counter — Group of flip-flops
connected in a special arrangement in which the states of the flip-flops represent
the binary number equivalent to the number of pulses that have occurred at the
input of the counter.
Binary Digit — Bit.
Binary Point — Mark that separates the
integer from the fractional portion of a binary quantity.
Binary System — Number system in which
there are only two possible digit values, 0 and 1.
Bipolar DAC — Digital-to-analog converter
that accepts signed binary numbers as input and produces the corresponding positive
or negative analog output value.
Bipolar ICs — Integrated digital circuits
in which NPN and PNP transistors are the main circuit elements.
BIT — In VHDL, the data object type representing
a single binary digit (bit).
Bit — Digit in the binary system.
Bit Array — A way to represent a group
of bits by giving it a name and assigning an element number to each bit's position.
This same structure is sometimes called a bit vector.
BIT_VECTOR — In VHDL, the data object
type representing a bit array. See also Bit Array.
Boolean Algebra — Algebraic process
used as a tool in the design and analysis of digital systems. In Boolean algebra
only two values are possible, 0 and 1.
Boolean Theorems — Rules that can
be applied to Boolean algebra to simplify logic expressions.
Bootstrap Program — Program, stored
in ROM, that a computer executes on power-up.
Bubbles — Small circles on the input or output
lines of logic-circuit symbols that represent inversion of a particular signal.
If a bubble is present, the input or output is said to be active-LOW.
Buffer/Driver — Circuit designed to
have a greater output current and/or voltage capability than an ordinary logic
circuit.
Buffer Register — Register that holds
digital data temporarily.
Buried Node — A defined point in a circuit
that is not accessible from outside that circuit.
Bus — Group of wires that carry related bits
of information.
Bus Contention — Situation in which
the outputs of two or more active devices are placed on the same bus line at
the same time.
Bus Drivers — Circuits that buffer the
outputs of devices connected to a common bus; used when a large number of devices
share a common bus.
Byte — Group of eight bits.
C — When used as an input label inside
an IEEE/ANSI symbol, an indication that the input controls the entry of data into
a storage element.
Cache — A high-speed memory system that can
be loaded from the slower system DRAM and accessed quickly by the high-speed
CPU.
Capacity — Amount of storage space in a
memory expressed as the number of bits or number of words.
Carry — Digit or bit that is generated when
two numbers are added and the result is greater than the base for the number
system being used.
Carry Propagation — Intrinsic circuit
delay of some parallel adders that prevents the carry bit (COUT)
and the result of the addition from appearing at the output simultaneously.
Carry Ripple — See Carry Propagation.
CAS (Column Address Strobe) — Signal used
to latch the column address into a DRAM.
CAS-before-RAS — Method
for refreshing DRAMs that have built-in refresh counters. When the CAS input
is driven LOW and held there as RAS is pulsed LOW, an internal refresh operation
is performed at the row address given by the on-chip refresh counter.
Cascading — Connecting logic circuits in
a serial fashion with the output of one circuit driving the input of the next,
and so on.
CASE — A control structure that selects one
of several options when describing a circuit's operation based on the value
of a data object.
Central Processing Unit (CPU) —
Part of a computer that is composed of the arithmetic/logic unit (ALU) and the
control unit.
Checksum — Special data word stored in the
last ROM location. It is derived from the addition of all other data words in
the ROM, and it is used for error-checking purposes.
Chip Select — Input to a digital device
that controls whether or not the device will perform its function. Also called
chip enable.
Circuit Excitation Table —
Table showing a circuit's possible PRESENT-to-NEXT state transitions and the
required J and K levels at each flip-flop.
Circular Buffer — A memory system
that always contains the last n data values that have been written. Whenever
a new data value is stored, it overwrites the oldest value in the buffer.
Circulating Shift Register —
Shift register in which one of the outputs of the last flip-flop is connected
to the input of the first flip-flop.
CLEAR — An input to a latch or FF used to make
Q = 0.
CLEAR State — The Q = 0 state
of a flip-flop.
Clock — Digital signal in the form of a rectangular
pulse train or a square wave.
Clock Skew — Arrival of a clock signal
at the clock inputs of different flip-flops at different times as a result of
propagation delays.
Clock Transition Times — Minimum
rise and fall times for the clock signal transitions used by a particular IC,
specified by the IC manufacturer.
Clocked D Flip-Flop — Type of
flip-flop in which the D (data) input is the synchronous input.
Clocked Flip-Flops — Flip-flops
that have a clock input.
Clocked J-K Flip-Flop — Type
of flip-flop in which inputs J and K are the synchronous inputs.
Clocked S-C Flip-Flop — Type
of flip-flop in which the inputs SET and CLEAR are the synchronous inputs.
CMOS (Complementary Metal-Oxide-Semiconductor) —
Integrated-circuit technology that uses MOSFETs as the principal circuit element.
This logic family belongs to the category of unipolar digital ICs.
Combinational Logic Circuits
— Circuits made up of combinations of logic gates, with no feedback from
outputs to inputs.
Comments — Text added to any HDL design
file or computer program to describe the purpose and operation of the code in
general or of individual statements in the code. Documentation regarding author,
date, revision, etc., may also be contained in the comments.
Common Anode — LED display that has
the anodes of all of the segment LEDs tied together.
Common Cathode — LED display that
has the cathodes of all of the segment LEDs tied together.
Common-Control Block — Symbol
used by the IEEE/ANSI standard to describe when one or more inputs are common
to more than one of the circuits in an IC.
Compiler — A program that translates a text
file written in a high-level language into a binary file that can be loaded
into a programmable device such as a PLD or a computer's memory.
Complement — See Invert.
Complex PLD (CPLD) — Class of
PLDs that contain an array of PAL-type blocks that can be interconnected.
COMPONENT — A VHDL keyword used at the
top of a design file to provide information about a library component.
Computer Word — Group of binary bits
that form the primary unit of information in a computer.
Concatenate — A term used to describe
the arrangement or linking of two or more data objects into ordered sets.
Concurrent — Events that occur simultaneously
(at the same time). In HDL, the circuits generated by concurrent statements
are not affected by the order or sequence of the statements in the code.
Concurrent Assignment Statement
— A statement in AHDL or VHDL that describes a circuit that works concurrently
with all other circuits that are described by concurrent statements.
Conditional Signal Assignment
— A VHDL concurrent construct that evaluates a series of conditions sequentially
to determine the appropriate value to assign to a signal. The first true condition
evaluated determines the assigned value.
Constants — Symbolic names that can be
used to represent fixed numeric (scalar) values.
Contact Bounce — The tendency of all
mechanical switches to vibrate when forced to a new position. The vibrations
cause the circuit to make contact and break contact repeatedly until the vibrations
settle out.
Contention — Two (or more) output signals
connected together trying to drive a common point to different voltage levels.
See also Bus Contention.
Control Bus — Set of signal lines that
are used to synchronize the activities of the CPU and the separate 
C
elements.
Control Inputs — Input signals synchronized
with the active clock transition that determine the output state of a flip-flop.
Control Unit — Part of a computer that
provides decoding of program instructions and the necessary timing and control
signals for the execution of such instructions.
Count Enable — An input on a synchronous
counter that controls whether the outputs respond to or ignore an active clock
transition.
Crystal-Controlled Clock Generator
— Circuit that uses a quartz crystal to generate a clock signal at a precise
frequency.
CUPL — Stands for Universal Compiler for Programmable
Logic. It is a computer program that takes an input file that describes how
a PLD is to operate, and converts it to output files that are used to program
the PLD.
Current-Sinking Logic — Logic
family in which the output of a logic circuit sinks current from the input of
the logic circuit that it is driving.
Current-Sinking Transistor —
Name given to the output transistor (Q4) of a TTL circuit.
This transistor is turned on when the output logic level is LOW.
Current-Sourcing Logic — Logic
family in which the output of a logic circuit sources, or supplies, current
to the input of the logic circuit that it is driving.
Current-Sourcing Transistor
— Name given to the output transistor (Q3) of most TTL
circuits. This transistor is conducting when the output logic level is HIGH.
Current Transients — Current spikes
generated by the totem-pole output structure of a TTL circuit and caused when
both transistors are simultaneously turned on.
D Flip-Flop — See
Clocked D Flip-Flop.
D Latch — Circuit that contains a NAND gate
latch and two steering NAND gates.
Data — Binary representations of numerical values
or nonnumerical information in a digital system. Data are used and often modified
by a computer program.
Data Acquisition — Process by which
a computer acquires digitized analog data.
Data Bus — Bidirectional lines that carry
data between the CPU and the memory, or between the CPU and the I/O devices.
Data Distributors — See
Demultiplexer.
Data-Rate Buffer — Application of
FIFOs in which sequential data are written into the FIFO at one rate and read
out at a different rate.
Data Selectors — See Multiplexer.
Data Transfer — See Parallel
Data Transfer or Serial Data Transfer
Decade Counter — Any counter capable
of going through 10 different logic states.
Decimal System — Number system that
uses 10 different digits or symbols to represent a quantity.
Decision Control Structures
— The statements and syntax that describe how to choose between two or
more options in the code.
Decoder — Digital circuit that converts an
input binary code into a corresponding single numeric output.
Decoding — Act of identifying a particular
binary combination (code) in order to display its value or recognize its presence.
DEFAULTS — An AHDL keyword used to establish
a default value for a combinational signal for instances when the code does
not explicitly specify a value.
DeMorgan's Theorems — (1) Theorem
stating that the complement of a sum (OR operation) equals the product (AND
operation) of the complements, and (2) theorem stating that the complement of
a product (AND operation) equals the sum (OR operation) of the complements.
Demultiplexer (DEMUX) — Logic
circuit that, depending on the status of its select inputs, will channel its
data input to one of several data outputs.
Density — A relative measure of capacity
to store bits in a given amount of space.
Dependency Notation — Method
used to represent symbolically the relationship between inputs and outputs of
logic circuits. This method employs the use of qualifying symbols embedded near
the top center or geometric center of a symbol element.
Differential Inputs — Method
of connecting an analog signal to an analog circuit's 1 and 2 inputs, neither
of which is ground, such that the analog circuit acts upon the voltage difference
between the two inputs.
Digital Computer — System of hardware
that performs arithmetic and logic operations, manipulates data, and makes decisions.
Digital Integrated Circuits
— Self-contained digital circuits made by using one of several integrated-circuit
fabrication technologies.
Digital One-Shot — A one-shot that
uses a counter and clock rather than an RC circuit as a time base.
Digital-Ramp ADC — Type of analog-to-digital
converter in which an internal staircase waveform is generated and utilized
for the purpose of accomplishing the conversion. The conversion time for this
type of analog-to-digital converter varies depending on the value of the input
analog signal.
Digital Representation — Representation
of a quantity that varies in discrete steps over a range of values.
Digital Signal Processing (DSP)
— Method of performing repetitive calculations on an incoming stream of
digital data words to accomplish some form of signal conditioning. The data
are typically digitized samples of an analog signal.
Digital Storage Oscilloscope
— Instrument that samples, digitizes, stores, and displays analog voltage
waveforms.
Digital System — Combination of devices
designed to manipulate physical quantities that are represented in digital form.
Digital-to-Analog Converter (DAC)
— Circuit that converts a digital input to a corresponding analog output.
Digitization — Process by which an analog
signal is converted to digital data.
Disable — Action in which a circuit is prevented
from performing its normal function, such as passing an input signal through
to its output.
Divide-and-Conquer — Troubleshooting
technique whereby tests are performed that will eliminate half of all possible
remaining causes of the malfunction.
Don't-Care — Situation when a circuit's
output level for a given set of input conditions can be assigned as either a
1 or a 0.
Down Counter — Counter that counts from
a maximum count downward to 0.
Downloading — Process of transferring
output files to a programming fixture.
DRAM Controller — IC used to handle
refresh and address multiplexing operations needed by DRAM systems.
Driver — Technical term sometimes added to
an IC's description to indicate that the IC's outputs can operate at higher
current and/or voltage limits than a normal standard IC.
Dual-in-Line Package (DIP) —
A very common IC package with two parallel rows of pins intended to be inserted
into a socket or through holes drilled in a printed circuit board.
Dual-Slope Analog-to-Digital
Converter — Type of analog-to-digital converter that linearly
charges a capacitor from a current proportional to VA for
a fixed time interval and then increments a counter as the capacitor is linearly
discharged to 0.
Dynamic RAM (DRAM) — Type of semiconductor
memory that stores data as capacitor charges that need to be refreshed periodically.
ECL — Emitter-coupled logic; also
referred to as current-mode logic.
Edge-Detector Circuit — Circuit
that produces a narrow positive spike that occurs coincident with the active
transition of a clock input pulse.
Edge-Triggered — Manner in which a
flip-flop is activated by a signal transition. A flip-flop may be either a positive-
or a negative-edge-triggered flip-flop.
Electrically Compatible —
When two ICs from different logic series can be connected directly without any
special measures taken to ensure proper operation.
Electrically Erasable
Programmable ROM (EEPROM) — ROM that can be electrically programmed,
erased, and reprogrammed.
Electrostatic Discharge (ESD)
— The often detrimental act of the transfer of static electricity (i.e.,
an electrostatic charge) from one surface to another. This impulse of current
can destroy electronic devices.
ELSE — A control structure used in conjunction
with IF/THEN to perform an alternate action in the case that the condition is
false. An IF/THEN/ELSE always performs one of two actions.
ELSIF — A control structure that can be used
multiple times following an IF statement to select one of several options in
describing a circuit's operation based on whether the associated expressions
are true or false.
Embedded Microcontroller —
Microcontroller that is embedded in a marketable product such as a VCR or an
appliance.
Emitter-Coupled Logic — See
ECL.
Enable — Action in which a circuit is allowed
to perform its normal function, such as passing an input signal through to its
output.
Encoder — Digital circuit that produces an
output code depending on which of its inputs is activated.
Encoding — Use of a group of symbols to
represent numbers, letters, or words.
ENTITY — Keyword in VHDL used to define the
basic block structure of a circuit. This word is followed by a name for the
block and the definitions of its input/output ports.
Enumerated Type — A VHDL user-defined
type for a signal or variable.
Equality Operator — A CUPL operator
that evaluates bit-by-bit equality between a set of variables and a constant.
Erasable Programmable ROM (EPROM)
— ROM that can be electrically programmed by the user. It can be erased
(usually with ultraviolet light) and reprogrammed as often as desired.
EVENT — A VHDL keyword used as an attribute
attached to a signal to detect a transition of that signal. Generally, an event
means a signal changed state.
Exclusive-NOR (XNOR) Circuit
— Two-input logic circuit that produces a HIGH output only when the inputs
are equal.
Exclusive-OR (XOR) Circuit — Two-input
logic circuit that produces a HIGH output only when the inputs are different.
Fan-Out — Maximum number of
standard logic inputs that the output of a digital circuit can reliably drive.
Field Programmable Gate Array
(FPGA) — Class of PLDs that contain an array of more complex logic
cells that can be very flexibly interconnected to implement high-level logic
circuits.
Field Programmable Logic
Array (FPLA) — A PLD that uses both a programmable AND array and
a programmable OR array.
Firmware — Computer programs stored in ROM.
First-In, First-Out (FIFO) Memory
— Semiconductor sequential-access memory in which data words are read
out in the same order in which they were written.
555 Timer — TTL-compatible IC that can
be wired to operate in several different modes, such as a one-shot and an astable
multivibrator.
Flash ADC — Type of analog-to-digital converter
that has the highest operating speed available.
Flash Memory — Nonvolatile memory IC
that has the high-speed access and in-circuit erasability of EEPROMs but with
higher densities and lower cost.
Flip-Flop — Memory device capable of storing
a logic level.
Floating Bus — When all outputs connected
to a data bus are in the Hi-Z state.
Floating Input — Input signal that
is left disconnected in a logic circuit.
Floppy Disk — Flexible magnetic disk
used for mass storage.
FOR Loop — See Iterative Loop.
4-to-10 Decoder — See BCD-to-Decimal
Decoder.
Frequency — The number of cycles per unit
time of a periodic waveform.
Frequency Counter — Circuit that
can measure and display a signal's frequency.
Frequency Division — The use of
flip-flop circuits to produce an output waveform whose frequency is equal to
the input clock frequency divided by some integer value.
Full Adder — Logic circuit with three
inputs and two outputs. The inputs are a carry bit (CIN) from
a previous stage, a bit from the augend, and a bit from the addend, respectively.
The outputs are the sum bit and the carry-out bit (COUT) produced
by the addition of the bit from the addend with the bit from the augend and
CIN.
Full-Custom — An application-specific
integrated circuit (ASIC) that is completely designed and fabricated from fundamental
elements of electronic devices such as transistors, diodes, resistors, and capacitors.
Full-Scale Error — Term used by
some digital-to-analog converter manufacturers to specify the accuracy of a
digital-to-analog converter. It is defined as the maximum deviation of a digital-to-analog
converter's output from its expected ideal value.
Full-Scale Output — Maximum possible
output value of a digital-to-analog converter.
Function Generator — Circuit that
produces different waveforms. It can be constructed using a ROM, a DAC, and
a counter.
Function Prototype — A text description
that contains all the essential defining attributes of a library function or
module.
Functionally Equivalent —
When the logic functions performed by two different ICs are exactly the same.
Fusible Link — Conducting material that
can be made nonconducting (i.e., open) by passing too much current through it.
Gate Array — An application-specific
integrated circuit (ASIC) made up of hundreds of thousands of prefabricated basic
gates that can be custom interconnected in the last stages of manufacture to form
the desired digital circuit.
GENERATE — A VHDL keyword used with the
FOR construct to iteratively define multiple similar components and to interconnect
them.
Glitch — Momentary, narrow, spurious, and
sharply defined change in voltage.
GSI — Giga-scale integration (1,000,000 gates
or more).
Half Adder — Logic circuit
with two inputs and two outputs. The inputs are a bit from the augend and a bit
from the addend. The outputs are the sum bit produced by the addition of the bit
from the addend with the bit from the augend and the resulting carry (COUT)
bit, which will be added to the next stage.
Hard Disk — Rigid metal magnetic disk used
for mass storage.
Hardware Description Language
(HDL) — A text-based method of describing digital hardware that
follows a rigid syntax for representing data objects and control structures.
Hexadecimal Number System —
Number system that has a base of 16. Digits 0 through 9 plus letters A through
F are used to express a hexadecimal number.
Hierarchical Design — A method
of designing a project by breaking it into constituent modules, each of which
can be broken further into simpler constituent modules.
Hierarchy — A group of tasks arranged in
rank order of magnitude, importance, or complexity.
High-Capacity PLD (HCPLD) —
A PLD with thousands of logic gates and many programmable macrocell resources,
along with very flexible interconnection resources.
High-Level Language — Computer
programming language that utilizes the English language in order to facilitate
the writing of a computer program.
Hold Time (tH)
— Time interval immediately following the active transition of the clock
signal during which the control input must be maintained at the proper level.
Hybrid System — System that employs
both analog and digital techniques.
IEEE/ANSI — Institute of
Electrical and Electronics Engineers/American National Standards Institute, both
professional organizations that establish standards.
IF/THEN — A control structure that evaluates
a condition and performs an action if the condition is true or bypasses the
action and continues on if the condition is false.
Immediate Addressing — Addressing
mode in which the part of the instruction following the op code is the actual
operand.
Indeterminate — Of a logic voltage
level, outside the required range of voltages for either logic 0 or logic 1.
Index — Another name for the element number
of any given bit in a bit array.
Inhibit Circuits — Logic circuits
that control the passage of an input signal through to the output.
Input Term Matrix — Part of a programmable
logic device that allows inputs to be selectively connected to or disconnected
from internal logic circuitry.
Input Unit — Part of a computer that facilitates
the feeding of information into the computer's memory unit or ALU.
Instructions — Binary codes that tell
a computer what operation to perform. A program is made up of an orderly sequence
of instructions.
INTEGER — In VHDL, the data object type representing
a numeric value.
Interfacing — Joining of dissimilar devices
in such a way that they are able to function in a compatible and coordinated
manner; connection of the output of a system to the input of a different system
with different electrical characteristics.
Interpolation Filtering —
Another name for oversampling. Interpolation refers to intermediate values inserted
into the digital signal to smooth out the waveform.
Invert — Cause a logic level to go to the
opposite state.
INVERTER — Also referred to as the NOT circuit;
logic circuit that implements the NOT operation. An INVERTER has only one input,
and its output logic level is always the opposite of this input's logic level.
Iterative Loop — A control structure
that implies a repetitive operation and a stated number of iterations.
Jam Transfer — See
Asynchronous Transfer.
JEDEC — Joint Electronic Device Engineering
Council, which established standards for IC pin assignments and PLD file format.
J-K Excitation Table — Table
showing the required J and K input conditions for each possible
state transition for a single J-K Flip-Flop.
Johnson Counter — Shift register
in which the inverted output of the last flip-flop is connected to the input
of the first flip-flop.
JTAG — Joint Test Action Group, which created
a standard interface that allows access to the inner workings of an IC for testing,
controlling, and programming purposes.
Karnaugh Map (K Map)
— Two-dimensional form of a truth table used to simplify a sum-of-products
expression.
Latch — Type of flip-flop; also,
the action by which a logic circuit output captures and holds the value of an
input.
Latch-Up — Condition of dangerously high
current in a CMOS IC caused by high-voltage spikes or ringing at device input
and output pins.
Latency — The inherent delay associated with
reading data from a DRAM. It is caused by the timing requirements of supplying
the row and column addresses, and the time for the data outputs to settle.
LCD — Liquid-crystal display.
Lead Pitch — The distance between the
centers of adjacent pins on an IC.
Least Significant Bit (LSB)
— Rightmost bit (smallest weight) of a binary expressed quantity.
Least Significant Digit (LSD)
— Digit that carries the least weight in a particular number.
LED — Light-emitting diode.
Libraries — A collection of descriptions
of commonly used hardware circuits that can be used as modules in a design file.
Library of Parameterized
Modules (LPM) — A set of generic library functions designed to
be very flexible in allowing the user to specify the number of bits, mod number,
control options, etc.
Linear Buffer — A first-in, first-out
memory system that fills at one rate and empties at another rate. After it is
full, no data can be stored until data is read from the buffer. See also
First In, First-Out (FIFO) Memory.
Linearity Error — Term used by some
digital-to-analog converter manufacturers to specify the device's accuracy.
It is defined as the maximum deviation in step size from the ideal step size.
Literals — In VHDL, a scalar value or bit
pattern that is to be assigned to a data object.
Load Operation — Transfer of data
into a flip-flop, a register, a counter, or a memory location.
Local Signal — See Buried Node.
Logic Array Block (LAB) —
A term Altera Corporation uses to describe building blocks of their CPLDs. Each
LAB is similar in complexity to an SPLD.
Logic Circuit — Any circuit that behaves
according to a set of logic rules.
Logic Elements — A term Altera Corporation
uses to describe the building blocks of their FLEX10K family of PLDs. The logic
elements are programmed as a RAM-based look-up table.
Logic Function Generation —
Implementation of a logic function directly from a truth table by means of a
digital IC such as a multiplexer.
Logic Level — State of a voltage variable.
The states 1 (HIGH) and 0 (LOW) correspond to the two usable voltage ranges
of a digital device.
Logic Primitive — A circuit description
of a fundamental component that is built into the MAX+PLUS II system of libraries.
Logic Probe — Digital troubleshooting
tool that senses and indicates the logic level at a particular point in a circuit.
Logic Pulser — Testing tool that generates
a short-duration pulse when actuated manually.
Look-Ahead Carry — Ability of some
parallel adders to predict, without having to wait for the carry to propagate
through the full adders, whether or not a carry bit (COUT)
will be generated as a result of the addition, thus reducing the overall propagation
delays.
Look-Up Table (LUT) — A way to
implement a single logic function by storing the correct output logic state
in a memory location that corresponds to each particular combination of input
variables.
Looping — Combining of adjacent squares in
a Karnaugh map containing 1s for the purpose of simplification of a sum-of-products
expression.
Low-Power Schottky TTL (LS-TTL)
— TTL subfamily that uses the identical Schottky TTL circuit but with
larger resistor values.
Low-Voltage Differential
Signaling (LVDS) — A technology for driving high-speed data lines
in low-voltage systems that uses two conductors and reverses the polarity to
distinguish between HIGH and LOW.
Low-Voltage Technology — New
line of logic devices that operate from a nominal supply voltage of 3.3 V or
less.
LSI — Large-scale integration (100 to 9999 gates).
MAC — An abbreviation for Multiply
Accumulate Unit, the hardware section of a DSP that multiplies a sample with a
coefficient and then accumulates (sums) a running total of these products.
MACHINE — An AHDL keyword used to create
a state machine in a design file.
Macrocell — A circuit made up of a group
of basic digital components such as AND gates, OR gates, registers, and tristate
control circuits that can be interconnected within a PLD via a program.
Macrofunctions — A term used by Altera
Corporation to describe the predefined hardware descriptions in their libraries
that represent standard IC parts.
Magnetic Disk Memory — Mass
storage memory that stores data as magnetized spots on a rotating, flat disk
surface.
Magnetic Tape Memory — Mass
storage memory that stores data as magnetized spots on a magnetically coated
plastic tape.
Magnitude Comparator — Digital
circuit that compares two input binary quantities and generates outputs to indicate
whether the inputs are equal or, if not, which is greater.
Main Memory — High-speed portion of a
computer's memory that holds the program and data the computer is currently
working on. Also called working memory.
Mask-Programmed ROM (MROM) —
ROM that is programmed by the manufacturer according to the customer's specifications.
It cannot be erased or reprogrammed.
Mass Storage — Storage of large amounts
of data; not part of a computer's internal memory.
Master/Slave Flip-Flops —
Obsolete flip-flops that have as their internal structure two flip-flops—a
master and a slave.
Maximum Clocking
Frequency (fMAX) — Highest frequency that may
be applied to the clock input of a flip-flop and still have it trigger reliably.
Mealy Model — A state-machine model
in which the output signals are controlled by combinational inputs as well as
the state of the sequential circuit.
Megafunctions — A complex or high-level
building block available in the Altera library.
Memory — Ability of a circuit's output to
remain at one state even after the input condition that caused that state is
removed.
Memory Cell — Device that stores a single
bit.
Memory Foldback — Redundant enabling
of a memory device at more than one address range as a result of incomplete
address decoding.
Memory Map — Diagram of a memory system
that shows the address range of all existing memory devices as well as available
memory space for expansion.
Memory Unit — Part of a computer that
stores instructions and data received from the input unit, as well as results
from the arithmetic/logic unit.
Memory Word — Group of bits in memory
that represents instructions or data of some type.
Microcomputer — Newest member of the
computer family, consisting of microprocessor chip, memory chips, and I/O interface
chips. In some cases, all of the aforementioned are in one single IC.
Microcontroller — Small microcomputer
used as a dedicated controller for a machine, a piece of equipment, or a process.
Microprocessor (MPU) — LSI chip
that contains the central processing unit (CPU).
Minuend — Number from which the subtrahend
is to be subtracted.
MOD Number — Number of different states
that a counter can sequence through; the counter's frequency division ratio.
Mode — The attribute of a port in a digital
circuit that defines it as input, output, or bidirectional.
Monostable Multivibrator —
See One-Shot.
Monotonicity — Property whereby the
output of a digital-to-analog converter increases as the binary input is increased.
Moore Model — A state-machine model in
which the output signals are controlled only by the sequential circuit outputs.
MOSFET — Metal-oxide-semiconductor field-effect
transistor.
Most Significant Bit (MSB) —
Leftmost binary bit (largest weight) of a binary expressed quantity.
Most Significant Digit (MSD)
— Digit that carries the most weight in a particular number.
MSI — Medium-scale integration (12 to 99 gates).
Multiplexer (MUX) — Logic circuit
that, depending on the status of its select inputs, will channel one of several
data inputs to its output.
Multiplexing — Process of selecting
one of several input data sources and transmitting the selected data to a single
output channel.
Multistage Counter — Counter in
which several counter stages are connected so that the output of one stage serves
as the clock input of the next stage to achieve greater counting range or frequency
division.
NAND Gate — Logic circuit
that operates like an AND gate followed by an INVERTER. The output of a NAND gate
is LOW (logic level 0) only if all inputs are HIGH (logic level 1).
NAND Gate Latch — Flip-flop constructed
from two cross-coupled NAND gates.
Negation — Operation of converting a positive
number to its negative equivalent, or vice versa. A signed binary number is
negated by the 2's-complement operation.
Negative-Going Transition —
When a clock goes from 1 to 0.
Nested — To have one control structure embedded
within another control structure.
Nibble — A group of four bits.
N-MOS (N-Channel Metal-Oxide-Semiconductor)
— Integrated-circuit technology that uses N-channel MOSFETs as the principal
circuit element.
NODE — A keyword in AHDL used to declare an
intermediate variable (data object) that is local to that subdesign.
Noise — Spurious voltage fluctuations that
may be present in the environment and cause digital circuits to malfunction.
Noise Immunity — Circuit's ability
to tolerate noise voltages on its inputs.
Noise Margin — Quantitative measure
of noise immunity.
Nonretriggerable One-Shot —
Type of one-shot that will not respond to a trigger input signal while in its
quasi-stable state.
Nonvolatile Memory — Memory that
will keep storing its information without the need for electrical power.
Nonvolatile RAM — Combination of
a RAM array and an EEPROM or flash on the same IC. The EEPROM serves as a nonvolatile
backup to the RAM.
NOR Gate — Logic circuit that operates like
an OR gate followed by an INVERTER. The output of a NOR gate is LOW (logic level
0) when any or all inputs are HIGH (logic level 1).
NOR Gate Latch — Flip-flop constructed
from two cross-coupled NOR gates.
NOT Circuit — See INVERTER.
NOT Operation — Boolean algebra operation
in which the overbar (
)
or the prime (') symbol is used to indicate the inversion of one or more logic
variables.
Objects — Various ways of representing
data in the code of any HDL.
Observation/Analysis — Process
used to troubleshoot circuits or systems in order to predict the possible faults
before ever picking up a troubleshooting instrument. When this process is used,
the troubleshooter must understand the circuit operation, observe the symptoms
of the failure, and then reason through the operation.
Octal Number System — Number
system that has a base of 8; digits from 0 to 7 are used to express an octal
number.
Octets — Groups of eight 1s that are adjacent
to each other within a Karnaugh map.
Offset Error — Deviation from the ideal
0 V at the output of a digital-to-analog converter when the input is all 0s.
In reality, there is a very small output voltage for this situation.
1-of-10 Decoder — See BCD-to-Decimal
Decoder.
1's-Complement Form — Result
obtained when each bit of a binary number is complemented.
One-Shot — Circuit that belongs to the flip-flop
family but that has only one stable state (normally Q = 0).
One-Time Programmable (OTP)
— A broad category of programmable components that are programmed by permanently
altering the connections (e.g., melting a fuse element).
Open-Collector Output — Type
of output structure of some TTL circuits in which only one transistor with a
floating collector is used.
Optical Disk Memory — Class of
mass memory devices that uses a laser beam to write onto and read from a specially
coated disk.
OR Gate — Digital circuit that implements
the OR operation. The output of this circuit is HIGH (logic level 1) if any
or all of its inputs are HIGH.
OR Operation — Boolean algebra operation
in which the symbol 1 is used to indicate the ORing of two or more logic variables.
The result of the OR operation will be HIGH (logic level 1) if one or more variables
are HIGH.
Output Logic Macrocell (OLMC)
— A group of logic elements (gates, multiplexers, flip-flops, buffers)
in a PLD that can be configured in various ways.
Output Unit — Part of a computer that
receives data from the memory unit or ALU and presents it to the outside world.
Overflow — When in the process of adding
signed binary numbers, a carry of 1 is generated from the MSB position of the
number into the sign bit position.
Override Inputs — Synonymous with
"asynchronous inputs."
Oversampling — Inserting data points
between sampled data in a digital signal to make it easier to filter out the
rough edges of the waveform coming out of the DAC.
PACKAGE — A VHDL keyword used
to define a set of global elements that are available to other modules.
Parallel Adder — Digital circuit made
from full adders and used to add all of the bits from the addend and the augend
together simultaneously.
Parallel Counter — See Synchronous
Counter.
Parallel Data Transfer — Operation
by which several bits of data are transferred simultaneously into a counter
or a register.
Parallel In/Parallel Out Register
— Type of register that can be loaded with parallel data and has parallel
outputs available.
Parallel In/Serial Out Register
— Type of register that can be loaded with parallel data and has only
one serial output.
Parallel Load — See Parallel
Data Transfer.
Parallel-to-Serial Conversion
— Process by which all data bits are presented simultaneously to a circuit's
input and then transmitted one bit at a time to its output.
Parallel Transmission — Simultaneous
transfer of all bits of a binary number from one place to another.
Parity Bit — Additional bit that is attached
to each code group so that the total number of 1s being transmitted is always
even (or always odd).
Parity Checker — Circuit that takes
a set of data bits (including the parity bit) and checks to see if it
has the correct parity.
Parity Generator — Circuit that
takes a set of data bits and produces the correct parity bit for the data.
Parity Method — Scheme used for error
detection during the transmission of data.
Percentage Resolution — Ratio
of the step size to the full-scale value of a digital-to-analog converter. Percentage
resolution can also be defined as the reciprocal of the maximum number of steps
of a digital-to-analog converter.
Period — The amount of time required for one
complete cycle of a periodic event or waveform.
Pin-Compatible — When the corresponding
pins on two different ICs have the same functions.
Pixel — Small dots of light that make up a
graphical image on a display.
P-MOS (P-channel Metal
Oxide Semiconductor) — Integrated-circuit technology that uses
P-channel MOSFETs as the principal circuit element.
PORT MAP — A VHDL keyword that precedes
the list of connections specified between components.
Positional-Value System —
System in which the value of a digit depends on its relative position.
Positive-Going Transition (PGT)
— When a clock signal changes from a logic 0 to a logic 1.
Power-Down — Operating mode in which a
chip is disabled and draws much less power than when it is fully enabled.
Power-Supply Decoupling —
Connection of a small RF capacitor between ground and VCC
near each TTL integrated circuit on a circuit board.
Power-Up Self-Test — Program stored
in ROM and executed by the CPU on power-up to test RAM and/or ROM portions of
the computer circuitry.
Preprocessor Commands — Compiler
commands that are processed before the main program code in order to control
how the code is interpreted.
Prescaler — A counter circuit that takes
base reference frequency and scales it by dividing the frequency down to a rate
required by the system.
PRESET — Asynchronous input used to set Q
= 1 immediately.
Presettable Counter — Counter
that can be preset to any starting count either synchronously or asynchronously.
Priority Encoder — Special type
of encoder that senses when two or more inputs are activated simultaneously
and then generates a code corresponding to the highest-numbered input.
PROCESS — A VHDL keyword that defines the
beginning of a block of code that describes a circuit that must respond whenever
certain signals (in the sensitivity list) change state. All sequential statements
must occur inside a process.
Product-of-Sums Form — Logic
expression consisting of two or more OR terms (sums) that are ANDed together.
Program — Sequence of binary-coded instructions
designed to accomplish a particular task by a computer; also, the act of entering
information into a programmable device (e.g., EPROM, PLD).
Program Counter (PC) — CPU register
that stores the address of the next instruction to be fetched.
Programmable Array Logic (PAL)
— Class of programmable logic devices. Its AND array is programmable,
whereas its OR array is hard-wired.
Programmable Interconnect
Array (PIA) — A term Altera Corporation uses to describe the resources
used to connect the LABs with each other and also with the input/output modules.
Programmable Logic Array (PLA)
— Class of programmable logic devices. Both its AND and its OR arrays
are programmable. Also called a field programmable logic array (FPLA).
Programmable Logic Device (PLD)
— IC that contains a large number of interconnected logic functions. The
user can program the IC for a specific function by selectively breaking the
appropriate interconnections.
Programmable Output Polarity
— Feature of many PLDs whereby an XOR gate with a polarity fuse gives
the designer the option of inverting or not inverting a device output.
Programmable ROM (PROM) —
ROM that can be electrically programmed by the user. It cannot be erased and
reprogrammed.
Programmer — A fixture used to apply the
proper voltages to PLD and PROM chips in order to program them.
Programming — The act of storing 1s and
0s in a programmable logic device to configure its behavioral characteristics.
Propagation Delays (tPLH/tPHL)
— Delay from the time a signal is applied to the time when the output
makes its change.
Pull-Down Transistor — See
Current-Sinking Transistor.
Pull-Up Transistor — See
Current-Sourcing Transistor.
Pulse — A momentary change of logic state
that represents an event to a digital system.
Pulse-Steering Circuit — A
logic circuit that can be used to select the destination of an input pulse,
depending on the logic levels present at the circuit's inputs.
Quantization Error —
Error caused by the nonzero resolution of an analog-to-digital converter. It is
an inherent error of the device.
Quasi-Stable State — State to
which a one-shot is temporarily triggered (normally Q = 1) before returning
to its stable state (normally Q = 0).
R/2R Ladder DAC
— Type of digital-to-analog converter whose internal resistance values span
a range of only 2 to 1.
Random-Access Memory (RAM) —
Memory in which the access time is the same for any location.
RAS (Row Address Strobe)
— Signal used to latch the row address into a DRAM chip.
RAS-Only Refresh — Method
for refreshing DRAM in which only row addresses are strobed into the DRAM using
the RAS input.
Read — Term used to describe the condition when
the CPU is receiving data from another element.
Read-Only Memory (ROM) — Memory
device designed for applications where the ratio of read operations to write
operations is very high.
Read Operation — Operation in which
a word in a specific memory location is sensed and possibly transferred to another
device.
Read/Write Memory (RWM) —
Any memory that can be read from and written into with equal ease.
Refresh Counter — Counter that keeps
track of row addresses during a DRAM refresh operation.
Refreshing — Process of recharging the
cells of a dynamic memory.
Register — Group of flip-flops capable of
storing data.
RESET — Term synonymous with "CLEAR."
RESET State — The Q = 0 state
of a flip-flop.
Resolution — In a digital-to-analog converter,
smallest change that can occur in the output for a change in digital input;
also called step size. In an analog-to-digital converter, smallest amount
by which the analog input must change to produce a change in the digital output.
Retriggerable One-Shot — Type
of one-shot that will respond to a trigger input signal while in its quasi-stable
state.
Ring Counter — Shift register in which
the output of the last flip-flop is connected to the input of the first flip-flop.
Ripple Counter — See Asynchronous
Counter.
Sample-and-Hold Circuit
— Type of circuit that utilizes a unity-gain buffer amplifier in conjunction
with a capacitor to keep the input stable during an analog-to-digital conversion
process.
Sampling — Acquiring and digitizing a data
point from an analog signal at a given instant of time.
Sampling Frequency — The rate
at which an analog signal is digitized (samples per second).
Sampling Interval — Time window
during which a frequency counter samples and thereby determines the unknown
frequency of a signal.
SBD — Schottky barrier diode used in all Schottky
TTL series.
Schematic Capture — A computer
program that can interpret graphic symbols and signal connections and translate
them into logical relationships.
Schmitt Trigger — Digital circuit
that accepts a slow-changing input signal and produces a rapid, oscillation-free
transition at the output.
Schottky TTL — TTL subfamily that uses
the basic TTL standard circuit except that it uses a Schottky barrier diode
(SBD) connected between the base and the collector of each transistor for faster
switching.
Selected Signal Assignment —
A VHDL statement that allows a data object to be assigned a value from one of
several signal sources depending on the value of an expression.
Self-Correcting Counter —
A counter that always progresses to its intended sequence, regardless of its
initial state.
Sensitivity List — The list of signals
used to invoke the sequence of statements in a PROCESS.
Sequential — Occuring one at a time in
a certain order. In HDL, the circuits that are generated by sequential statements
behave differently, depending on the order of the statements in the code.
Sequential-Access Memory (SAM)
— Memory in which the access time will vary depending on the storage location
of the data.
Sequential Circuit — A logic circuit
whose outputs can change states in synchronism with a periodic clock signal.
The new state of an output may depend on its current state as well as the current
states of other outputs.
Serial Data Transfer — Transfer
of data from one place to another one bit at a time.
Serial In/Parallel Out — Type
of register that can be loaded with data serially and has parallel outputs available.
Serial In/Serial Out — Type
of register that can be loaded with data serially and has only one serial output.
Serial Transmission — Transfer
of binary information from one place to another a bit at a time.
SET — An input to a latch or FF used to make
Q = 1.
Set — A grouping of concatenated variables or
signals.
SET State — The Q = 1 state of a
flip-flop.
Settling Time — Amount of time that
it takes for the output of a digital-to-analog converter to go from 0 to within
one-half step size of its full-scale value as the input is changed from all
0s to all 1s.
Setup Time (tS) — Time
interval immediately preceding the active transition of the clock signal during
which the control input must be maintained at the proper level.
Shift Register — Digital circuit that
accepts binary data from some input source and then shifts these data through
a chain of flip-flops one bit at a time.
Sigma (
) — Greek letter that
represents addition and is often used to label the sum output bits of a parallel
adder.
Sigma/Delta Modulation — Method
of sampling an analog signal and converting its data points into a bit stream
of serial data.
Sign Bit — Binary bit that is added to the
leftmost position of a binary number to indicate whether that number represents
a positive or a negative quantity.
Sign-Magnitude System — A system
for representing signed binary numbers where the most significant bit represents
the sign of the number and the remaining bits represent the true binary value
(magnitude).
Simple PLD (SPLD) — A PLD with
a few hundred logic gates and possibly a few programmable macrocells available.
Simulator — Computer program that calculates
the correct output states of a logic circuit based on a description of the logic
circuit and on the current inputs.
Speed-Power Product — Numerical
value (in joules) often used to compare different logic families. It is obtained
by multiplying the propagation delay by the power dissipation of a logic circuit.
Spike — See Glitch.
SSI — Small-scale integration (fewer than 12
gates).
Staircase Test — Process by which
a digital-to-analog converter's digital input is incremented and its output
monitored to determine whether or not it exhibits a staircase format.
Staircase Waveform — Type of waveform
generated at the output of a digital-to-analog converter as its digital input
signal is incrementally changed.
Standard Cell — An application-specific
integrated circuit (ASIC) made of predesigned logic blocks from a library of
standard cell designs that are interconnected during the system design stage
and then fabricated on a single IC.
Standard Logic — The large assortment
of basic digital IC components available in various technologies as MS and SSI
chips.
State Machines — A sequential circuit
that advances through several defined states.
State Table — A table whose entries represent
the sequence of individual FF states (i.e., 0 or 1) for a sequential binary
circuit.
State Transition Diagram —
A graphic representation of the operation of a sequential binary circuit, showing
the sequence of individual FF states and conditions needed for transitions from
one state to the next.
Static Accuracy Test — Test
in which a fixed binary value is applied to the input of a digital-to-analog
converter and the analog output is accurately measured. The measured result
should fall within the expected range specified by the digital-to-analog converter's
manufacturer.
Static RAM (SRAM) — Semiconductor
RAM that stores information in flip-flop cells that do not have to be periodically
refreshed.
STD_LOGIC — In VHDL, a data type defined
as an IEEE standard. It is similar to the BIT type, but it offers more possible
values than just 1 or 0.
STD_LOGIC_VECTOR — In VHDL, a data
type defined as an IEEE standard. It is similar to the BIT_VECTOR type, but
it offers more possible values than just 1 or 0 for each element.
Step Size — See Resolution.
Straight Binary Coding — Representation
of a decimal number by its equivalent binary number.
Strobe — Another name for an enable input
usually used to latch a value into a register.
Strobing — Technique often used to eliminate
decoding spikes.
Structural Level of Abstraction
— A technique for describing a digital circuit that focuses on connecting
ports of modules with signals.
SUBDESIGN — Keyword in AHDL used to begin
a circuit description.
Substrate — Piece of semiconductor material
that is part of the building block of any digital IC.
Subtrahend — Number that is to be subtracted
from a minuend.
Successive-Approximation ADC
— Type of analog-to-digital converter in which an internal parallel register
and complex control logic are used to perform the conversion. The conversion
time for this type of analog-to-digital converter is always the same regardless
of the value of the input analog signal.
Sum-of-Products Form — Logic
expression consisting of two or more AND terms (products) that are ORed together.
Supercomputers — Computers with the
greatest speed and computational power.
Surface Mount — A method of manufacturing
circuit boards whereby ICs are soldered to conductive pads on the surface of
the board.
Synchronous Control Inputs —
See Control Inputs.
Synchronous Counter — Counter
in which all of the flip-flops are clocked simultaneously.
Synchronous Systems — Systems
in which the circuit outputs can change states only on the transitions of a
clock.
Synchronous Transfer — Data
transfer performed by using the synchronous and clock inputs of a flip-flop.
Syntax — The rules defining keywords and their
arrangement, usage, punctuation, and format for a given language.
Test Vector — Sets of inputs
used to test a PLD design before the PLD is programmed.
Timing Diagram — Depiction of logic
levels as related to time.
Toggle Mode — Mode in which a flip-flop
changes states for each clock pulse.
Toggling — Process of changing from one
binary state to the other.
Top-Down — A design method that starts at
the overall system level and then defines a hierarchy of modules.
Totem-Pole Output — Term used to
describe the way in which two bipolar transistors are arranged at the output
of most TTL circuits.
Transducer — Device that converts a physical
variable to an electrical variable (e.g., a photocell or a thermocouple).
Transmission Gate — See
Bilateral Switch.
Transparent — Of a D latch, operating
so that the Q output follows the D input.
Trigger — Input signal to a flip-flop or
one-shot that causes the output to change states depending on the conditions
of the control signals.
Tristate — Type of output structure that
allows three types of output states: HIGH, LOW, and high-impedance (Hi-Z).
Truth Table — Logic table that depicts
a circuit's output response to the various combinations of the logic levels
at its inputs.
TTL (Transistor/Transistor Logic)
— Integrated-circuit technology that uses the bipolar transistor as the
principal circuit element.
2's-Complement Form — Result
obtained when a 1 is added to the least significant bit position of a binary
number in the 1's-complement form.
Type — The attribute of a variable in a computer-based
language that defines its size and how it can be used.
ULSI — Ultra-large-scale integration
(100,000 or more gates).
Unasserted — Term used to describe the
state of a logic signal; synonymous with "inactive."
Undersampling — Acquiring samples of
a signal at a rate less than twice the highest frequency contained in the signal.
Unipolar ICs — Integrated digital circuits
in which unipolar field-effect transistors (MOSFETs) are the main circuit elements.
Up Counter — Counter that counts upward
from 0 to a maximum count.
Up/Down Counter — Counter that can
count up or down depending on how its inputs are activated.
Up/Down Digital-Ramp ADC —
Type of analog-to-digital converter that uses an up/down counter to step up
or step down the voltage from a digital-to-analog converter until it intersects
the analog input.
VARIABLE — A keyword in AHDL
used to begin a section of the code that defines the names and types of data objects
and library primitives. A keyword used in VHDL to declare a local data object
within a PROCESS.
Very
High Speed Integrated Circuit (VHSIC) Hardware Description Language (VHDL)
— A hardware description language developed by the Department of Defense
to document, simulate, and synthesize complex digital systems.
VLSI — Very large-scale integration (10,000
to 99,999 gates).
Volatile Memory — Memory requiring
electrical power to keep information stored.
Voltage-Controlled Oscillator
(VCO) — Circuit that produces an output signal with a frequency
proportional to the voltage applied to its input.
Voltage-Level Translator —
Circuit that takes one set of input voltage levels and translates it to a different
set of output levels.
Voltage-to-Frequency ADC —
Type of analog-to-digital converter that converts the analog voltage to a pulse
frequency that is then counted to produce a digital output.
Weighted Average —
An average calculation of a group of samples that assigns a different weight
(between 0.0 and 1.0) to each sample.
Wired-AND — Term used to describe the logic
function created when open-collector outputs are tied together.
Word — Group of bits that represent a certain
unit of information.
Word Size — Number of bits in the binary
words that a digital system operates on.
WRITE — Term used to describe the condition
when the CPU is sending data to another element.
Write Operation — Operation in which
a new word is placed into a specific memory location.